Touch@Glass for partners
For Tecomat Foxtrot system integrators, architects and design engineers.
Touch@Glass | Touch@Glass EVO
CIB bus, 1 to 4 modules under one glass.
Touch@Glass
Touch buttons with RGB LEDs and a segment display; temperature and humidity sensor as standard, can also be ordered without sensors.
Touch@Glass EVO
The new generation: touch buttons with RGB LEDs and a dot-matrix LED display, built-in temperature and humidity sensor; optional ambient light and proximity sensor and haptic feedback.
Overview
Bus | CIB of the Tecomat Foxtrot system, power and data over a single cable |
Power supply | 24 V or 27 V DC from the CIB bus |
Consumption | 30–65 mA per switch module, see the table below |
Sizes | 1 to 4 modules side by side or one above the other; module 94 × 94 mm; vertical version without display |
Series | Touch@Glass (segment display) or Touch@Glass EVO (dot-matrix display); they cannot be combined under one glass |
Modules | CO₂ and the RFID reader can be added under one glass; fingerprint reader standalone only (1 module) |
Back box | min. 30 mm (45 mm recommended); fingerprint reader min. 45 mm (60 mm recommended) |
Glass | 4 mm safety tempered, printed to the project design, replaceable; automatic calibration within 40 seconds after the glass is removed |
Ordering | from Teco a.s. via the B2B catalog |
Documentation | datasheets at /en/downloads/, design in the configurator |
Wiring
- Direct connection to the CIB bus, with no converter and no extra app.
- Touch@Glass terminal block: +CIB−, AI1, GND, AI2, +24V, GND, DO; CIB address on the label.
- Can be combined under one glass: a Touch@Glass switch or a Touch@Glass EVO switch, the CO₂ module and the RFID reader, 1 to 4 modules in total.
- Cannot be combined: Touch@Glass and Touch@Glass EVO under one glass.
- Standalone only: fingerprint reader (1 module, 94 × 94 mm), on the CIB bus alongside the other switches.
Power supply and consumption
module | power supply | rated current |
|---|---|---|
Touch@Glass / EVO, 1 module | 24 / 27 V DC from CIB | 30–65 mA |
2 modules | 60–130 mA | |
3 modules | 90–195 mA | |
4 modules | 120–260 mA | |
CO₂ | max. 30 mA, 2 mA idle | |
fingerprint reader | max. 30 mA, 2 mA idle | |
RFID reader | typ. 20 mA, max. 80 mA |
CIB bus (according to TECO documentation):
Units per branch | max. 32; a switch with 2, 3 or 4 modules takes up 2, 3 or 4 addresses |
Line current | max. 1 A (CF-2141, CF-2142, CP-2000, C-BS-0001M bus separator); the internal masters CP-2005, CP-2007, CP-2080, CP-2090, CP-2091 supply only up to 100 mA, use the C-BS-0001M bus separator for higher consumption |
Voltage | 24 V DC without backup / 27.2 V DC with backup, tolerance 20.4–30 V |
Length | max. 500 m from the master |
Topology | any (line, star, branches), no ring, no termination |
Cable | twisted shielded pair, e.g. J-Y(St)Y 1×2×0.8 (conductor diameter 0.8 mm) |
Foxtrot 2 branches | CP-2000: 2 internal lines; CP-2005/ |
- RFID reader: handled from Mosaic.
Mosaic
In Mosaic, the switch is added in the I/O Configurator as a CIB unit. The data structures are the same as in the Touch@Glass and Touch@Glass EVO datasheets.
input structure | description |
|---|---|
DI | state of binary inputs DI1 and DI2, short and long pulse on the input |
AI_STAT | status byte of the analog inputs and the internal thermometer and hygrometer (range overflow, measurement validity) |
AI1, AI2 | analog input value [°C], [kΩ], [mV] |
GLASS. | current state of buttons 1 to 6 |
GLASS. | short press of buttons 1 to 6 |
GLASS. | long press of buttons 1 to 6 |
GLASS. | EVO: light intensity in lux (if the sensor is fitted) |
GLASS. | EVO: proximity sensor active, sensor and display communication errors |
THERM | temperature [°C] |
RH | humidity [%] |
output structure | description |
|---|---|
GLASS. | module control word: display on, binary output DO1 (max. 30 V / 3 A); EVO additionally haptic feedback, WiFi and firmware upload |
GLASS. | RGB LED at each button (blue, red, green) |
DISPA | value to show on the display, range –32,768 to 32,767 |
ZONE, ICONS | EVO: number formatting and predefined texts on the dot-matrix display |
DLIGHT, BLIGHT | display and LED brightness [%] |
- On the CO₂ module, GLASS.
VALUE carries the CO₂ concentration in ppm. - Optional external temperature sensor (Pt1000, Ni1000, NTC 12k, KTY81-121) or measurement of resistance up to 100 kΩ and voltage 0–2 V on the AI inputs.
Dimensions and installation
modules | glass size | buttons |
|---|---|---|
1 | 94 × 94 mm | 6 |
2 | 165 × 94 mm | 12 |
3 | 236 × 94 mm | 18 |
4 | 307 × 94 mm | 24 |
- Orientation: Switches can be mounted horizontally or vertically; the vertical version has no display. You choose the orientation in the configurator. For the vertical version, the dimensions in the table are the height; the width is 94 mm.
- Back box: min. 30 mm, 45 mm recommended. Fingerprint reader: min. 45 mm, 60 mm recommended.
- Protection rating: IP40 front, IP20 rear.
- Operating temperature: 0 to +50 °C, humidity max. 80%.
- Replacing an existing wall switch: possible where there is a CIB bus and a box at least 30 mm deep.
- Installation instructions and drawings: in the datasheets at /en/downloads/.
Graphics and glass
Glass | 4 mm safety tempered, abrasion-resistant |
Surface | smooth · satin matte · with recesses (only 1–2 modules fitted exclusively with buttons; not with CO₂, RFID or fingerprint reader) |
Graphics | design from a collection, custom pictograms, room labels, logo; design and printing included in the price of the glass |
Glass replacement | for button modules no service visit needed, automatic calibration within 40 seconds after the glass is removed; for the fingerprint reader and RFID reader by a professional service technician |
Design collections
Black & White
Black, white, gray and anthracite for clean interiors
Minimalist
Muted tones from sand beige to terracotta and navy
Intense
A rich color range from azure to mustard
Natura
Wood decors: oak, walnut, maple and ebony
Marble
Stone and marble from travertine to golden stone
Metal
Brushed metals, metallics, brass and rust
Creativity
Designs with a story: paper, music, flowers
Configurator
- Modules, glass, design and button labels.
- The design is sent to TECO as an inquiry.
Specification text
For inserting into a technical report or bill of quantities. Adjust the values in brackets.
Wall-mounted glass smart switch Touch@Glass [EVO] for the CIB bus of the Tecomat Foxtrot system, [1/2/3/4]-module, glass size [94/165/236/307] × 94 mm, 4 mm safety tempered glass printed to the project design, [6/12/18/24] touch buttons with RGB LEDs, [segment/dot-matrix] display, [internal temperature and humidity sensor], power supply and communication from the CIB bus 24/27 V DC, IP40 protection from the front, mounting in a flush-mounting box at least 30 mm deep (45 mm recommended). Supplier Teco a.s.
The configurator generates the assembly order code in the form C-WS-[buttons][surface][modules]R[-TG2]-[displays], for example C-WS-12S2R-TG2-M1W (two-module Touch@Glass EVO, satin matte glass, 12 buttons, one white dot-matrix display).
Ordering
Service
Technical Support | MICRONIC Přerov s.r.o., +420 773 768 693, podpora@ |
Warranty | 24 months |
Delivery time for glass with graphics | 4 weeks |
Replacement glass | including printing and custom graphic design: a price-list item by size (1–4 modules) and surface (smooth / satin matte / with recesses), ordered from TECO like any other item; glass with recesses only for 1- and 2-module switches fitted exclusively with buttons. For the fingerprint reader and RFID reader, the glass is fitted by a professional service technician. |